Everything on model trains, model railroads, model railways, locomotives, model train layouts, scenery, wiring, DCC and more. Enjoy the world's best hobby... model railroading!

Can I Run a DCC Engine on DC?

Henry models N Scale and asks readers:

“I just purchased a DCC switcher for my small Switching layout. My layout is DC. When I try to run the engine it is either to fast or stopped. The engine is a Backmann Spectrum with DCC and DC operation. The engine will not move on DC until I have almost full throttle. Is their any way to lower the starting voltage in DC operation so that I can use it as a switcher for a john Allen Timetable game?”

4 Responses to Can I Run a DCC Engine on DC?

  • Jaysays:

    Almost all DCC decoder equipped locomotives have the option to run on DC. The option can be programmed to be disabled, or enabled. Sounds like yours is enabled. Dcc equipped loco’s will not turn on until the power is at least around 8VDC, and that is because it takes at least that amount of power to activate the decoder’s circuits. If your loco has sound, it will be easier to tell what level of voltage the decoder comes on. Once the threshold level is set, you can control the loco’s direction by throwing you control’s reverse switch. If it’s going too fast, you will have to “fine tune” the voltage level to get the desired speed. You will have to play with it to get the feel for when it is in “Idle” or “Off”.

  • Greg Wiblesays:

    It takes about 7 volts DC to get your DCC/DC engine working. First sound, bell, horn. It usually starts slowly then picks up speed. Just let it go untill it reaches the speed you want. Then drive it with your throttle.

  • Frank Bsays:

    I have a few DCC locos but only DC control, and as Jay says, they only start running at around 8 to 10 volts because the control circuit needs that much voltage to turn itself on.

    Therefore there is only a small voltage range in which you have useful control of the speed.

    To achieve better fine control, use a controller with a large dial, so that the effective voltage range is spread over a larger mechanical rotation of the dial.

    Some of my DCC locos have a feature which requires a voltage polarity flip switch, so that flipping the switch over, or over and back quickly, will activate the bell and whistle, while the loco continues forwards.

    Attached image shows how to wire this.

  • henry Robbinssays:

    Thanks guys. The info you all gave me is helpful.

Leave a Reply to henry RobbinsCancel reply

Your email address will not be published. Required fields are marked *

Add a photo or image related to your comment (JPEG only)

Mining Town Plans

scale model mining town models

N Scale Track Plans

Watch Video

Everything DCC

Download Your Free Catalog

Use Tiny Railroad Micro Controllers

A micro controller is basically a small programmable computer device to help the model railroader “make things operate.” It is clever way to realistically replicate the movements, actions and functions you are likely to see on a full size railroad.


Submit Your Model Railroading Questions!

Before you submit your model railroading question please add some feedback, answers or comments to other postings on this model train blog. What goes around comes around... so if you can help others in the hobby, someone else may help you.

Important - Please add plenty of supporting details to any question you submit (eg. scale, solutions you have already tried etc.) , as the clearest and best questions usually get the best answers. Also, please check your spelling and punctuation as all questions need to be approved by the blog moderator prior to publication. Approved questions are normally published within a week (if not sooner).

Submit your model train questions here.

Watch These Club Videos

Club members access helpful new resources each month: diagrams, video tutorials, articles, track plans and more. Watch the tour videos here.

Scenery Techniques Explained



Model Train Help Ebook

Scenery & Layout Ideas

Share With Friends


Submit Your Article

Would you like to write an article and have it published?

Preference will be given to articles that help others progress in the hobby, maybe suggesting an idea for their layout, a quick tip or two... or perhaps a little bit of good advice based on your model railroading experiences.

We are all in this hobby together, so the more we can do to share ideas and help each other, the better.

Submit Your Article Here

It’s YOUR Railroad!

Your rolling stock and locomotives might actually be the center of attention on your layout, but the scenic features that surround and envelop your layout is what's likely to make your train setup stand proud of the rest. Your selection of scenery and structures will add an element of customization that will make your railroad truly unique.

Scenery, structures, and fine detailing is a fundamental aspect of any good model railroad, particularly if it is intended to replicate a true-to-life railroading scene. How realistic or authentic you make your railroad is entirely up to you... and you alone.

Some enthusiasts like to replicate every tiny detail so as to accurately depict, in every aspect, a miniaturized version of a real life scene.

Others in this hobby adopt a more "free-style" approach and choose to mix and match accessories and features they personally prefer. Even though the purist will possibly be unimpressed with unrealistic or out of context elements, it is YOUR railroad layout so you can make it anything you personally want!

Model Railroading Blog Archive

Reader Poll

Sorry, there are no polls available at the moment.